GG is a manufacturing concern managed by Defense Distributed.
How much does Ghost Gunner cost?
The total cost of the machine is $3,249.99. before shipping is applied. We now offer a layaway option. Please contact us at [email protected] for more details.
What materials can the GG3-S cut?
Ghost Gunner can cut all grades of aluminum and several grades of steel, including low carbon (1008, A36), medium carbon (1018, 1045), and stainless steel (303, 304, 316). It can also engrave titanium, brass, and other non-ferrous metals.
What is included with my Ghost Gunner?
Ghost Gunner CNC, 6' USB A-B cable, 6' NEMA 5-15/IEC C13 three prong power cable, 17mm & 12mm combination wrench, allen key set, and a USB drive with the software, cutting codes and the GG3 Operators Manual.
What else do I need to buy for the machine to work?
If you already have a computer, all you need is a starter kit and the workpiece for that kit. For example an AR15 starter kit and an 80% AR15 lower receiver. Starter kits are multi-use, you only need one to finish multiple receivers.
What end mills does Ghost Gunner use?
The ghost gunner uses standard end mills. We use ER-11 collet system. This allows 5/16” or 8mm maximum shank size. We include the proper end mills in our starter kits.
Which 80% receivers does Ghost Gunner use?
GG3 can machine any of the following: Mil-spec AR-15, DPMS 308 lower receiver (Gen 1), M1911 Series 70 (steel or aluminum), and G80s 120R receivers. Our jigs and fixtures support a wide range of receiver types.
How is the work piece held on the table?
Depending on the starter kit/platform, there are metal or plastic fixtures that hold the workpiece on the table for probing/milling. Starter kits include necessary hardware to hold the fixture and worpiece in place.
Yes you can! Ghost Gunner runs standard G-Code via an onboard grbl interpreter. You can use software like Fusion 360 to generate toolpaths and export G-Code for Ghost Gunner.
How fast can the machine run?
When cutting aluminum, there's little reason to cut as fast as possible. Ghost Gunner prioritizes accuracy and finish quality over speed. A typical AR-15 lower takes about 1 hour to complete.
How does GG3-S power or rigidity compare to other CNC machines?
GG3-S is not as powerful or rigid as a half-ton knee mill or a six-figure Haas, but it is the most rigid and capable desktop CNC in its class. The machine is built from aluminum unibodies inside a plasma-cut A36 steel enclosure.
Do I need a special power supply?
No. Ghost Gunner uses a standard IEC power cord and is compatible with any 110/220V circuit. No external compressor or coolant system is required.
How do I connect to Ghost Gunner?
Ghost Gunner has two ports: Power (IEC standard) and USB (Type 'B').
What sort of maintenance is required for Ghost Gunner?
Ghost Gunner's moving parts are entirely sealed from chip debris. All bearings are sealed and contain permanent lubricant. Simply oil the lead screws and linear rails periodically.
What Open Source parts did Ghost Gunner design?
The entire machine is open source. For other open source designs, Ghost Gunner developed a custom spindle motor and VFD controller board. All source files are available on our Downloads page.
When does my order ship?
All machines are made to order. When placing your order, the GG3 Deposit page will indicate your shipping timeline.
Is manufacturing a firearm legal?
Under federal law, manufacturing firearms for purpose of sale and distribution without an FFL is prohibited. However, an individual may make a firearm for personal use without a license. Please check your state and local laws.
In what states is Ghost Gunner prohibited?
Ghost Gunner CNC machines are general purpose machines classified by the US Department of Commerce. However some states have restrictions on machines with the primary purpose of making firearms. Due state regulations, we do not ship Ghost Gunner machines to California, New Jersey or Massachusetts.
