Ghost Gunner 3 Deposit

$500.00

Ghost Gunner 3 allows you to manufacture firearms with confidence and ease, in the privacy of your own home. GG3 removes material 5 times faster than GG2 and the new unibody construction provides greater rigidity, drastically improving finished part quality.

The custom spindle is powered by a specially designed closed-loop digital VFD, which sets a new standard in desktop CNC machining. GG3 ships with code to complete 80% AR-15, AR-308, M1911, and Polymer 80 frames frames. All existing jigs are compatible with GG3.

Click here to see a full list of the new features

Reserve your unit today

Product Details

Ghost Gunner 3 is a general purpose CNC mill that gives you the ability to finish 80% receivers and frames with ease, in the comfort of your own home.

By placing this deposit, you reserve your place on the GG3 waitlist. You will be asked to complete your order in Q1 of 2020 at which point your unit will be shipped. The full price of the machine is $2,100.00 and your deposit goes toward that total price. To find out about financing your unit, click here

Ghost Gunner 3 is a complete redesign based on the successes of the GG2. It uses a milled, precision unibody frame for sharply improved squareness and rigidity. Optical limit switches and pre-loaded, self-aligning ballscrews allow it to deliver advanced positional accuracy.

GG3 incorporates a custom motion-control board with a closed loop, digital VFD controller. The machine accepts g-code from most CAM post-processors, and supports tool diameters up to 8 mm (~5/16”).

Included with the GG3: A DD USB with all our latest software. ER-11 collet nut, 5/16″ allen wrench, 3mm ball-end allen wrench, 12mm wrench, 17mm wrench, 6′ USB A-B cable, 6′ three-prong power cable. Laptop not included. Shipping is a flat rate of $100 in the United States.

Lower Guide

To begin your project, order one of our Starter Kits, which includes everything you need to get milling. For best results, use 80% lowers/frames, fixtures, and tooling designed to work specifically with the Ghost Gunner platform.

Ghost Gunner 2 uses the following DD lower files:

It is also compatible with the following g-code suites:

We cannot currently recommend anodized lowers or frames, but for additional information on anodized lowers or frames please email us at support@ghostgunner.net.

Tech Specs

System Requirements
Windows 7+, Mac OSX 10.13+

 

Parameter Value Unit Note
Weight 19 Kg ~42 pounds
X/Y/Z travel 89/242/79 mm Double the GG2 build volume
X/Y/Z interior clearance 116/299/162 mm Measurements with cover on
Peak Spindle Power 375 W Overload protection prevents exceeding
Continuous Spindle Power 190 W Long-term average, temperature limited. Can be exceeded.
Spindle speed 3000-9000 rpm Variable, closed loop. Can apply full power at any rpm.
Max Linear Velocity 2600 mm/min 260% faster than GG2
Max Linear Acceleration 250 mm/s^2 8 times more than GG2
Spindle runout 0.0009 in Measured on tapered collet, 1mm from tip
T-Slot Spacing 40 mm Center-to-center
Table T-slots 2 QTY Compatible with 20 mm T-nuts
Collet system ER11 Accepts tools up to 8 mm

See more detailed specifications here.

Customer Reviews

4.8 Based on 58 Reviews
5 ★
88% 
51
4 ★
9% 
5
3 ★
3% 
2
2 ★
0% 
0
1 ★
0% 
0
Write a Review

Thank you for submitting a review!

Your input is very much appreciated. Share it with your friends so they can enjoy it too!

Filter Reviews:
RH
07/13/2018
Randel H.

Revolutionary.

I've used my Ghost Gunner to make one thing, in the privacy of my one bedroom apartment. At the press of a button, (and some minor easy to follow setup tasks and even easier clean-up) and 3-4 hours later I have an untraceable AR-15 Lower Receiver. Highly recommended to anyone who supports the 2nd amendment.

MW
06/24/2018
Michael W.

Ghost Gunner 2

Awesome piece of machinery. Easy to setup and use. DDCut walks you though the whole process. I have complete a couple of AR lowers. Looking forward to ordering the 1911 jig and building one of those next. Thanks!

MH
06/01/2018
Matthew H.

Ghost Gunner 2

Awesome machine! Very easy to use even if you don't have a manufacturing background. The customer support is extremely awesome as well. Very happy with my machine.

MB
05/21/2018
Marc B.

Awesome 2nd amendment maker

We love our toys and hate to be told we can't have them.. thank you to the people willing to fight for what is right the machine of ghosts

KA
05/21/2018
Keith A.

After some use...

Dear GG, I waited to write this review till after having done a few projects. After learning a few "tricks" that shorten the set up a little, I am still unhappy about the time it takes to set everything up. Part of this due to the device and the jigs being small, cramped, and delicate. The 3 mm screws are VERY easily dropped into the inside of the device. The wrench provided needs to be at least 3 inches longer to get to the inside "T" nuts. I have arthritis in my hands so admittedly I have poor dexterity, but even so a friend without such limitations was cussing a bit trying to get the jig set-up. The whole work area needs to be bigger, more open, for adult size hands to work the tiny pieces like the mounting screws. The jigs themselves should be bigger. I found the AR15 jig is so low to the table that cutting shavings build up and short the work piece to that table, which causes the CNC to lose track of where it is. This causes the end mill to try to cut too much and causes the spindle to bog down and stop. I found if I take the chip cover off about 2/3 the way through the well cutting and vacuum the chips away, the complete cutting process will occur without incident. If the jig where thicker and held the work piece up away from the chips this would help. Another problem is the 5/32 drill. The one provided was not perfectly true so cause the holes to be slightly over size. I went to the local industrial supply house and purchased a high-end titanium bit and that solved that problem... All in all I am moderately happy with the device. After trial and error I can now produce a professional quality product, but it is not without stressing out trying to put little screws into tight places. I strongly recommend you either change your design to be easier to work on, or have an over 60 model for us old guys that need reader glasses and help with small items... Keith Abernethy

Product Details

Ghost Gunner 3 is a general purpose CNC mill that gives you the ability to finish 80% receivers and frames with ease, in the comfort of your own home.

By placing this deposit, you reserve your place on the GG3 waitlist. You will be asked to complete your order in Q1 of 2020 at which point your unit will be shipped. The full price of the machine is $2,100.00 and your deposit goes toward that total price. To find out about financing your unit, click here

Ghost Gunner 3 is a complete redesign based on the successes of the GG2. It uses a milled, precision unibody frame for sharply improved squareness and rigidity. Optical limit switches and pre-loaded, self-aligning ballscrews allow it to deliver advanced positional accuracy.

GG3 incorporates a custom motion-control board with a closed loop, digital VFD controller. The machine accepts g-code from most CAM post-processors, and supports tool diameters up to 8 mm (~5/16”).

Included with the GG3: A DD USB with all our latest software. ER-11 collet nut, 5/16″ allen wrench, 3mm ball-end allen wrench, 12mm wrench, 17mm wrench, 6′ USB A-B cable, 6′ three-prong power cable. Laptop not included. Shipping is a flat rate of $100 in the United States.

Lower Guide

To begin your project, order one of our Starter Kits, which includes everything you need to get milling. For best results, use 80% lowers/frames, fixtures, and tooling designed to work specifically with the Ghost Gunner platform.

Ghost Gunner 2 uses the following DD lower files:

It is also compatible with the following g-code suites:

We cannot currently recommend anodized lowers or frames, but for additional information on anodized lowers or frames please email us at support@ghostgunner.net.

Tech Specs

System Requirements
Windows 7+, Mac OSX 10.13+

 

Parameter Value Unit Note
Weight 19 Kg ~42 pounds
X/Y/Z travel 89/242/79 mm Double the GG2 build volume
X/Y/Z interior clearance 116/299/162 mm Measurements with cover on
Peak Spindle Power 375 W Overload protection prevents exceeding
Continuous Spindle Power 190 W Long-term average, temperature limited. Can be exceeded.
Spindle speed 3000-9000 rpm Variable, closed loop. Can apply full power at any rpm.
Max Linear Velocity 2600 mm/min 260% faster than GG2
Max Linear Acceleration 250 mm/s^2 8 times more than GG2
Spindle runout 0.0009 in Measured on tapered collet, 1mm from tip
T-Slot Spacing 40 mm Center-to-center
Table T-slots 2 QTY Compatible with 20 mm T-nuts
Collet system ER11 Accepts tools up to 8 mm

See more detailed specifications here.